Price: $31.40 - $29.94
(as of Dec 31, 2024 12:34:25 UTC – Details)
The 360 degree fixture mounted motion sensor from Lithonia lighting is designed to save energy and money by automatically turning lights on when you need them and off when you don’t. Perfect for operating single or multiple fixtures in commercial and residential locations. It is easy to install and wire to led or fluorescent bay lights, strip lights and wraparound light fixtures.
Provides automatic on and off for single or multiple fixtures for energy savings and convenience
White acrylic housing matches white light fixtures
360 degree passive infrared technology provides up to 60 feet of motion detection at floor level
Works with led or fluorescent bay lights, strip lights and wraparound light fixture
Adjustable time delay, preset to 15 minutes
William Carson –
bettb
This works great. I had to modify the installation because I used it on flush mounted fluorescent lights that could not be accessed from the end where it was intended to be mounted. Mounted it on the inside corner and cut a square out of the lens so the cover can be lowered to replace the bulbs. Works great. The next on I get will be able to install it as intended because they will be surface mounted lights.
Stan –
great motion sensor
Easy to install and program, would buy again. Had it for 5 months and no problems. Installed in our pantry for the light and couldn’t be more please,no more pull chain to deal with.
Anchorman-CET –
It has worked for 2+ years
I bought this in October 2018. It has worked flawlessly for all this time. Like so many others my only complaint is the instructions. I shiver with dread anytime I think about changing the shut-off timer. Regardless, it’s been very reliable thus far.
Cucas –
THE INSTRUCTIONS ARE SIMPLY AWFUL… TOOK ME …
THE INSTRUCTIONS ARE SIMPLY AWFUL…TOOK ME HOURS ON THE WWW BEFORE I FOUND ENOUGH INFORMATION TO PROPERLY HOOK UP THE WIRING… HOWEVER IT DOES APPEAR TO BE WORKING SATISFACTORILY…
Ranger Rick –
Seems to work OK. The installation information is OK …
Seems to work OK. The installation information is OK but the programming instructions are awful. I found these details instructions online.Time Delay Program Instructions1. Push and hold button until LED flashes rapidly (approximately 6seconds). Release button.2. Press button twice to enter Time Delay adjustment mode. The LEDwill flash back the current Time Delay setting according to below table(i.e. 5 flashes for 10 minute Time Delay).3. Wait approximately 3 seconds4. Press button the number of times for the desired setting (i.e., presstwice for 2.5 minutes Time Delay).5. LED will flash back this new setting, (repeated up to 10 times).Press button down again until LED flashes rapidly (approximately 6seconds). Release button.6. Press button twice to verify Time Delay has been reprogrammed.LED will flash back twice indicating acceptance of new settingTime Delay Settings TablePush Button the number of increments desired1 ~ 30 Sec 2 ~ 2.5 Min 3 ~ 5.0 Min4 ~ 7.5 Min 5 ~ 10.0 Min 6 ~ 12.5 Min7 ~ 15.0 Min 8 ~ 17.5 Min 9 ~ 20.0 Min
Joe Donnelly –
Works as advertised
Had my electrician install it. He likes it, I like it. It works great. Going to buy a second one
Jeff Hammer –
Wiring not easy
NOTE: If ballast disconnect plugs are cut, white wire with red stripe is Neutral. Cap off plain white wire.” I listened to that instruction, capping off the plain white wire (in the set of three). However, the light would not work with that wire out of the equation. I ended up having to wire both the white wire and red-stripe white wire to the ballast’s white wire. Then it finally worked! I read in one of the other reviews that someone else had to do this. So beware of this note in the instructions.
Mumof2 –
Works as expected.
Works perfectly and was delivered fast from the US to Canada. This item was not available where I live. Only need it for motion 15 feet away from the room amd it works perfect!